Notice to Use Plat Compactor

1. Please elevate the end of the rammer first before you start it and put the wheel on the end of the rammer by using of the bearing rod. Then check all parts of the rammer before working. The passive belt pulley and wheel should be rotated flexibly when you rotate it and they can’t produce obvious radial displacement and axial translation. The bolts of the vibrating box and other fastening bolts should be fastened tightly before working.

2. After starting the rammer, you can operate it if there is no abnormal sound. Otherwise you should close the rammer immediately and check it.

3. The loose earth to be rammed should be paved levelly and the thickness of the earth layer can’t exceed 200mm. Otherwise the rammer may sink into the earth and can’t advance.

4. Hold down the handrail softly on the slope or the loose ground so as to accelerate the advancing speed.

5. Please add lubricating oil to the bearings of the vibrating box after every 15 working days. Check the rammer thoroughly and maintain it after accumulative 80 working hours. Especially check whether the matching of the bearing in the vibrating box and the outer covering, axle is loose. If some of these parts are worn out, replace them immediately.

6. Please pay attention to the working condition of the rammer during you operate it. If there is abnormal sound or the temperature of the vibrating box bearing is too high, please close the rammer immediately and check it.

7. All fastening bolts need to be fastened tightly after the rammer is reassembled.

8. Before the rammer works, put the wheel under the ramming plate first, then start the rammer. When you need to move the rammer, do not elevate the handrail but through the handles on both sides of the ramming.


    Get a Free Quote

    Interested in our products? Please give your inquiry in the form below. We will reply you in 12 hours.

    * Your Name

    * Your Email

    * Your Phone Number

    Your Country

    * Your Requirement

    *We respect your privacy, and will not share your personal information with other entities.

    How to Use Electric Tamping Rammer

    Pre-operating preperation

    1、Please ready the manual carefully, and grasp it’s main points.

    2、Please ensure that the bolts and every part of the rammer are fastened every time before operating the rammer.

    3、Please ensure that the lubricating oil is adequate every time before operating the rammer

    4、Please ensure that the ground wire line of the electromotor is earthed and the insulated wire line is safe and intact.

    5、 Please switch the electromotor to “OFF” position, and then turn on the current.

    6、 After starting the electromotor, please ensure the rotating direction of the electromotor is right (it should be clockwise as per the direction of the blade).

     

    During operating

    1、 Please operate the rammer on the level and compact ground.

    2、 You can control the working condition of the rammer by control switch of the electromotor after starting the electromotor

    3、 Don’t hold the handrail too tightly so long as you can prevent the rammer from tilting and control the advancing speed and direction. You can change the advancing direction by rotating the handrail.

    4、 Do not hold down the handrail strongly so as not to affect the bounce height of the rammer.

    5、 By rotating the handrail, you may not only make the rammer move forward as required, but make it rotating at the original place.

    6、 Hold down the handrail lightly on the slope or the loose ground so as to accelerate the advancing speed.

    7、This kind of rammer is a small-sized ramming machine, so the earth which need to be rammed should be rammed layer by layer, each layer should be less than 250mm. Each layer should be rammed repeatedly for three times or more where it is needed.

    8、 If the rammer need to be moved, you can raise the handrail a little, push the walking wheel into the coupler, and then put down the handrail and make sure the strength is at the end of the rammer, and then push the rammer forward.

     

    Caution

    1、 Make sure the ground wire line of the plug is reliable earthed, which can not be connected with live wire. Please check the insulator surface of the line, so as to avoid electricity leakage.

    2、 During operation, Please make the guide line suitable. If too tight, it may be broken.

    3、 Make sure the connecting plug of the electromotor is in a sound condition. If unfastened, electricity leakage may occur.

    4、 Make sure the rammer is kept off moisture. And do not work while raining.

    5、 Do not operate on the cement or other hard ground.

    6、 Please stop to check immediately if there is some abnormal sound while working.


      Get a Free Quote

      Interested in our products? Please give your inquiry in the form below. We will reply you in 12 hours.

      * Your Name

      * Your Email

      * Your Phone Number

      Your Country

      * Your Requirement

      *We respect your privacy, and will not share your personal information with other entities.

      Trouble Diagnosing and Clearing of Plate Compactor

      Conventional Trouble Trouble Reason Clearing Way
      Vibrating frequency
      decrease and the ramming
      force weaken
      1. V-belt loosens.

      2. The grinding sheet in

      the clutch wheel is worn
      out.

      1. Adjust the position of
      the gasoline engine and
      tighten the V-belt.
      2. Replace the grinding
      sheet.
      The temperature of the
      vibrating box is too high and
      the noise increase
      1. The bearing is lack of
      lubricating oil.
      2. The outer circle of the
      bearing rotates and the
      bearing base is worn out.
      3. The bearing is
      damaged.
      1. Add lubricating grease.
      2. Replace the bearing
      base or repair it.
      3. Replace the bearing.
      Abnormal sound during
      working
      1. The bolts loosen or the
      spring washer breaks off.
      2. The bearing is
      damaged.
      3. The outer circle of the
      bearing rotates and the
      bearing base is worn out.
      1. Fasten the bolts or
      replace the spring
      washer.
      2. Replace the bearing.
      3. Replace the bearing
      base or eliminate the
      clearance.
      The handrail vibrates
      strongly or the engine base
      collides with the ramming  plate
      The rubber spring is damaged Replace the rubber spring
      Oil leakage of the bearing The oil seal is damaged Replace the oil seal

        Get a Free Quote

        Interested in our products? Please give your inquiry in the form below. We will reply you in 12 hours.

        * Your Name

        * Your Email

        * Your Phone Number

        Your Country

        * Your Requirement

        *We respect your privacy, and will not share your personal information with other entities.

        Ellsen factory purchase new facilities again

        Ellsen factory integrates advanced facilities including hobbing machine, grinding machine, drilling machine, vertical drilling machine, vertical milling machine, CNC lathe and hydraulic press etc. Thesestate-of-the-art infrastructure allows us to manufacture bulk and urgent orders of clients within stipulated time. Our production unit is fully equipped with latest machinery, they are powerful guarantee to control quality and cost.

        20151118023036710


          Get a Free Quote

          Interested in our products? Please give your inquiry in the form below. We will reply you in 12 hours.

          * Your Name

          * Your Email

          * Your Phone Number

          Your Country

          * Your Requirement

          *We respect your privacy, and will not share your personal information with other entities.

          Electric Make Coil Machine’s Operation

          This machine is the new-style equipment which professional development for iron art roller. Using the automated design,can easily processed into rolling coil products using the fishplate materials be heated, easy to operate.

          20151119111815729

          Processing one time will be able to shape, greatly improve the working efficiently.Machine operation CD will come with machine to be sent to clients.


            Get a Free Quote

            Interested in our products? Please give your inquiry in the form below. We will reply you in 12 hours.

            * Your Name

            * Your Email

            * Your Phone Number

            Your Country

            * Your Requirement

            *We respect your privacy, and will not share your personal information with other entities.

            How To Use The Steel Bar Bending Machine?

            With the vigorous development of construction industry in recent years, developing countries need more steel bar processing machines to support infrastructure. But there are some clients, especially trader customers do not know the correct operation way totally. One of our client from Colombia who bought the bending machine for the first time, so we shoot videos to teach him how to use the machine.

            And there are some preparation work before operation for your reference:

            1. There must be enough space and the ground must be smooth which will ensure the operation convenience and the equipment’s bottom is indeed on the ground.

            2. Before operating, the machine’s spare parts should be checked whether it’s broken or loose and the electrical wiring is safe and the electric motor connect earth wire. Installing earth leakage circuit breaker before using.

            3. To check if there is enough oil in the case and the oil cup of main shaft.

            4. At the first operation, the equipment should run no-load 15 to 30 minutes. During the period, user check whether abnormal noise and phenomenon exists and the button is sensitive and effective.

            5. Before the normal operation, inspection should be done in advance:

            ※ Electrical switch is safe and effective.

            ※ To ensure there’s no abnormal noise and phenomenon after the equipment powered on.

            6. Operating over-loaded is strictly forbidden.


              Get a Free Quote

              Interested in our products? Please give your inquiry in the form below. We will reply you in 12 hours.

              * Your Name

              * Your Email

              * Your Phone Number

              Your Country

              * Your Requirement

              *We respect your privacy, and will not share your personal information with other entities.

              Ellsen Factory Purchase New Facilities Again

              20151119025025491
              Ellsen factory integrates advanced facilities including hobbing machine, grinding machine, drilling machine, vertical drilling machine, vertical milling machine, CNC lathe and hydraulic press etc. These state-of-the-art infrastructure allows us to manufacture bulk and urgent orders of clients within stipulated time. Our production unit is fully equipped with latest machinery, they are powerful guarantee to control quality and cost.


                Get a Free Quote

                Interested in our products? Please give your inquiry in the form below. We will reply you in 12 hours.

                * Your Name

                * Your Email

                * Your Phone Number

                Your Country

                * Your Requirement

                *We respect your privacy, and will not share your personal information with other entities.

                The Maintenance of Steel Bar Cutting Machine

                The necessary spare parts will be offered to clients come with machine, as below photo. It is good for your more long time usage and convenient maintenance.
                Machinery product need a short time adapt using, when some problems happened, there are some trouble diagnosing and removing idea for you.
                20151119021455772

                Conventional Trouble Cause Removing way
                Blade fails to come out
                1.The tension spring of the clutch is damaged.
                2.The pedal fastening screw loose.
                3.The motor rotate reversely.
                1.Replace the spring.
                2.Fasten the fastening screw.
                3.Modulate the connection of
                motor to ensure rotation direction accord with the mark.
                Clutch control failure
                (Blade keeps coming out)
                1.The axis of the clutch is bent.
                2.The clutch press spring lose efficacy.
                3.The torsional spring of pedal axis lose efficacy.
                1. Adjust or change the axis of clutch.
                2. Replace the press spring.
                3. Replace the torsional spring
                Fails to cut big-diameter
                steel bar
                1.The belt is too tight.
                2.The belt lose efficacy.
                3.There are oil stain on belt.
                1. Adjust the belt suitably.
                2. Replace the belt.
                3. Eliminate the oil stain.

                  Get a Free Quote

                  Interested in our products? Please give your inquiry in the form below. We will reply you in 12 hours.

                  * Your Name

                  * Your Email

                  * Your Phone Number

                  Your Country

                  * Your Requirement

                  *We respect your privacy, and will not share your personal information with other entities.

                  Ellsen Straightening Cutting Machine’s Features

                  Engaged in offering construction machines, we have emerged as a renowned name in the domestic market. Below are mentioned few our straightening cutting machine features that make our organization to stand miles ahead of our competitors:

                  1. The adoption of totally steel made gear, integral connecting rod, and heat treatment and hardness treatment of the important parts of the machine together guarantee a long working time.

                  2. The thread type and adjustable stop gauge ensure the accuracy and immobility of positioning.

                  3. The separation of connecting rod and gear enable the machine undertake a reasonable stress.

                  4. The connecting rod and gear can be disassembled separately which is convenient for maintenance.

                  5. The large cutting stroke ensures all standards of steel bar can be cut without changing the cutting blade.

                  Some photos showing our machine details:

                  20151119025544691


                    Get a Free Quote

                    Interested in our products? Please give your inquiry in the form below. We will reply you in 12 hours.

                    * Your Name

                    * Your Email

                    * Your Phone Number

                    Your Country

                    * Your Requirement

                    *We respect your privacy, and will not share your personal information with other entities.

                    What are the Different Types of Rebar? And Does it Matter?

                    The compressive strength of concrete is tremendous. Incredible force is required to crush concrete. However, concrete has relatively weak tensile strength. Far less force is required to crack concrete by bending or twisting it than is required to crush concrete.

                    A variety of rebar lengths and diameters are available, but there are only six common types of rebar: European (a carbon, manganese, silicon, etc. alloy); carbon steel (basic “black” rebar); galvanized; epoxy coated; glass-fiber-reinforced-polymer (GFRP); and stainless steel. The different types of rebar each unique strengths and weaknesses.

                    20151208055256218

                     

                    European Rebar– The strength of European rebar is its cost. Made principally of manganese, European rebar is the least resistant type of rebar with respect to bending. While easy to work with, it is generally not recommended for use in areas that experience earthquakes nor for projects that require substantial structural integrity from its rebar.

                    Carbon Steel Rebar– The most common rebar, “black” bar is used on every type and scale of project with few exceptions. The biggest weakness of black rebar is that it corrodes. When rebar corrodes, it expands cracking and breaking the concrete around it. For situations in which the rebar might be exposed to humidity or water saturation, there are better options than black rebar. However, with respect to is value/tensile strength ratio, black rebar is the best rebar available.

                    Epoxy-Coated Rebar– Epoxy-coated rebar is black rebar with an epoxy coat. It has the same textile strength, but is 70 to 1,700 times more resistant to corrosion. However, the epoxy coating is incredibly delicate. The greater the damage to the coating, the less resistant to corrosion.

                    Galvanized Rebar– Galvanized rebar is only forty times more resistant to corrosion than black rebar, but it is more difficult to damage the coating of galvanized rebar. In that respect, it has more value than epoxy-coated rebar. However, it is about 40% more expensive than epoxy-coated rebar.

                    Glass-Fiber-Reinforced-Polymer (GFRP)– GFRP is a composite much like carbon fiber. As a result, field bends are not permitted when using GFRP. However, it will not corrode, period. In that respect, GFRP is an unparalleled concrete reinforcement bar. While it costs ten times as much as epoxy coated rebar per pound, it is extremely light, so the cost is only about double when considering talking linear feet.

                    Stainless Steel Rebar– Stainless steel rebar is the most expensive reinforcing bar available, about eight times the price of epoxy-coated rebar. It is also the best rebar available for most projects. However, using stainless steel in all but the most unique of circumstances is often overkill. But, for those who have a reason to use it, stainless steel rebar 1,500 times more resistant to corrosion than black bar; it is more resistant to damage than any of the other corrosive-resistant or corrosive-proof types or rebar; and it can be bent in the field.


                      Get a Free Quote

                      Interested in our products? Please give your inquiry in the form below. We will reply you in 12 hours.

                      * Your Name

                      * Your Email

                      * Your Phone Number

                      Your Country

                      * Your Requirement

                      *We respect your privacy, and will not share your personal information with other entities.